I am sorry to hear that there were some issues happening for you. But whatever they were, they seem to be resolved. The Blue Ox Base Plate Kit # BX2614 you were looking at would not be the correct base plate kit, but we do have the kit that you need.
- Blue Ox Base Plate Kit # BX2675
This base plate kit is confirmed to fit your 2018 Ford F-350 Super Duty and will provide the attachment points needed for the tow bar. I have also listed out additional parts needed to flat tow your F-350.
Tow... view full answer...
I recommend the Air Lift LoadLifter 7500 XL Air Helper Springs - Rear Axle item # AL86KV. Not only are they a confirmed fit for your 2022 Ford F-350 FX4 4WD but they are the only air bags that are compatible with 5th Wheel Hitches. These airbags have a 7,500 lbs capacity. The 7" Diameter LoadLifter 7500 XL air springs upgrade your rear suspension for high-quality, full-time load support. They also level your Ford F-350 Super Duty, improve braking and ride comfort, and reduce the strain... view full answer...
When it comes to installing a front mount hitch on your 2022 Ford F-350 Super Duty The Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2 inch # C31078 will work. This hitch has an easy, bolt-on installation with no welding required. The hitch has a line pull up to 9,000 pounds and has a gross trailer weight up to 5,000 pounds. Per the instructions you can put the hitch into the lowered position or the raised position, so you will not have any clearance issues.
I attached the installation... view full answer...
Based off of my research, your Honda EU3000UIS Inverter has a dry weight of 130.7-lbs.
With that being said, the MORryde RV Generator Slide Out Tray # MR37FR would be the closest we can offer that can work for you. This tray has a maximum weight capacity of 800-lbs, and the tray measures 34-1/4" long, and 22-7/8" wide.
Since your generator measures 25.9" long, 7.6" wide, and 22" tall, this is the closest cargo tray we offer that can fit your generator.
This slide out tray also weighs... view full answer...
The easiest way to get 12V charging power to the 7-way contact on your 2017 F-350 is simply to add a separate charging line circuit. This saves you dealing with the missing contacts in the fuse box.
All you need is a 40-amp breaker # PK54540, enough 10-gauge wire # 10-1-1 to reach from the battery to the 7-way, wire loom # 459075-1, ring terminals # DW05705-1 and butt connector set # 05732-2. The wire and loom are both sold by the foot so order enough to give you some extra length just... view full answer...
The Weigh Safe 2-Ball Mount w/ Built-In Scale - 2 inch Hitch - 6 inch Drop, 7 inch Rise - 12.5K WS6-2 will have the towing capacity that you will need. This 2 ball system comes with one 2 inch ball rated for 8,000 pounds, and one 2-5/16 inch hitch ball rated for 12,500 pounds, and has a tongue weight of 1,500 pounds. The hitch balls are stainless steel and are corrosion resistant. Per Weigh Safe there shanks were previously rated for 10,000 pounds but later on learned that they could tow... view full answer...
Unfortunately the longest garnish available has a 6" long leg like the Ceiling Garnish for Fan-Tastic Vents Roof Vent - 6" Leg - 14-1/4" x 14-1/4" - White # FVK1060-81. Typically the garnishes are trimmed down to fit, but you don't need it to span the whole 6-1/2" and it's ok if it's a bit short; the outside will also be sealed up and any small gap wouldn't be seen. view full answer...
It sounds like you need an Under-Bed Rail and Installation Kit # RP87FR for your 2019 Ford F-350. The Reese puck system is the same as the Ford OEM prep package, although, to be safe you should measure for yourself to verify.
The capacity of this kit will vary depending on if you use the welded on brackets # RP88FR or the bolt on inner brackets # RP27FR. If you use the bolt on brackets # RP27FR then your capacity is 20,000 lbs, and if you use the weld on brackets # RP88FR, then the capacity... view full answer...
I've got a quick and easy solution for you with the Curt T-Connector Vehicle Wiring Harness # C55384. This tees in behind your current 4-Way/7-Way using the US CAR connection and gives you an additional 4-Way that you'll be able to use the same time your 7-Way is being used.
I recommend picking up the Brophy Mounting Bracket # BK4F and N-Drill Mounting Bracket # 18136 so the additional 4-Way can be held in a place that has easy access. view full answer...
You'll need a puck adapter that's compatible with the Ford OEM puck spacing. The Curt # C88KR would be an excellent choice, which would add 2-1/2 inches of height to your hitch.
I've linked to a product description video for the adapter I recommended. view full answer...
We actually only carry one htich cover for 2-1/2 hitch receivers, part # C22277, which obviously isn't an American Flag.
Instead you can use a reducer like part # 325-GH-007 with a 2 inch cover witih an American flag, part # AMG102202. view full answer...
When using The Hopkins Smart Hitch Backup Camera and Hitch Aligner System # HM50002 both the camera and monitor of the camera receive their power from the vehicle's reverse light circuit. The circuit is accessed when the round U.S. Car connector is plugged into the factory 7 way.
The monitor's cable plugs into the camera assembly which is then routed under the vehicle to the cab of the truck. You can check and make sure there is no dirt or foreign material trapped inside the plug's contacts.... view full answer...
I actually may have a better solution for you on this. Since your new 2020 Ford F-350 comes with the OEM Prep package already installed, you can use the existing hitch head from your B&W Hitch and pair it with the Replacement Base for B&W Companion OEM 5th Wheel Trailer Hitch for Ford Super Duty # BWRVB3300. This would provide you with a base that is compatible with the OEM pucks on your new F-350 that you can mount your old head to. It's a bit cheaper than going with a completely new system... view full answer...
You can use the Super Titan Forged Pintle Hook Plate for 3" Trailer Hitches - 25,000 lbs # RP38186 as the pintle hitch mount to fit in the 3" hitch receiver on your 2018 Ford F-350. This will give you a hitch mounted base to use a pintle hook like the Pintle Hook, Bolt-On, 30K # C48215 and you won't need to use hitch reducers any longer!
I've linked some review videos of these parts for you to have a look at, as well. view full answer...
For your 2005 Ford F-350 with the Remov-A-Ball your options will be limited. As far as a 5th wheel hitch being compatible with your current system, that isn't going to be an option as there are none available.
What you can do, is use the Convert-A-Ball Cushioned 5th-Wheel-To-Gooseneck Adapter # CAB-C5GX1216
which will lock overtop of the kingpin on your 5th wheel, and hook-up to your existing gooseneck ball.
I should note also, that some manufacturers won't allow this adapter without... view full answer...
Without knowing what brand of universal base rails you have for your 2019 Ford F-350, I won't be able to recommend the correct frame brackets, however what I can tell you is that it may be easier to install a fresh set of base rails.
If you're interested in this route, I recommend checking out the Reese Quick-Install Custom Outboard Installation Kit w/ Base Rails for 5th Wheel Trailer Hitches # RP56017-53.
This kit includes also includes the frame brackets, the needed installation hardware,... view full answer...
If you have the Hollywood Racks RV Rider Bike Rack # HLY64FR then this already has 5" wheel cradles. If you have the Hollywood Racks Sport Rider SE2 Bike Rack # HR1450Z, HR1450E, HR1455E, HR1450Z-E, or HR1455Z-E, then you can use Fat Bike Adapter Kit # HR89FR to accommodate 5" wide tires. I attached a demonstration video for you. view full answer...
Since your 2015 F-350 Super Duty has the factory 5th wheel prep package you'll want to use the Reese Elite Series Underbed Rail Adapter # RP30156.
This adapter accommodates standard 5th-wheel trailer hitches with weight ratings of 15,000 lbs, 16,000 lbs, or 20,000 lbs. You can still use your 25K-rated hitch but the system capacity will be 20,000-lbs overall. view full answer...
No, you will not need to use a spacer. Since the lift ended up being only 1" higher than the factory lift you will not need a spacer like the Lift Spacers for Firestone Ride-Rite Air Helper Springs # F2366 when installing an airbag system like the Firestone Ride-Rite Air Helper Springs # F2550 in your truck. The # F2550 is the correct Firestone Ride-Rite Air Helper Springs for your 2010 Ford F-350.
The Air Command Compressor System # F2610 will work with the # F2550 if you want a compressor... view full answer...
For your Companion 5th wheel hitch # BWRVK3305 with a 3/8 inch hole, I recommend the Master Lock Python Adjustable Cable Lock - 6' Cable # 8419DPF. The cable lock can be run through the same locations on both sides and attaches to itself.
A padlock is another option you have with the Master Lock Padlock # ML4140LH.
Included are video resources for both solutions. view full answer...
Go To Results